Single Steroid Oil

Nandrolone Decanoate (300mg/ml)

Lean Muscle Building Steroids Oil Nandrolone Decanoate (300mg/ml)

Cook Recipes

100 ml of Deca (300mg/ml)
30 grams powder  22.5ml
57.5 ml sesame oil
5 ml BA 5%
15 ml BB 15%

Dosage

Dosage: If you’re supplementing with Deca-Durabolin for your off-season gains, as most will be, a dosing of 200mg per week will be the minimum performance dosing, with 400mg per week being the high-end dose for most men and all they ever need. Some men will find a need to go as high as 600mg per week, but there is no reason to ever go above this amount, and such amounts should only be attempted by the very experienced. If joint relief is all you’re after, 100mg per week will do the trick, but the vast majority of performance enhancers will supplement with at least 200mg per week.

Half Life: In any case, regardless of total dosing most Deca-Durabolin use will extend to at least 8 weeks, with 10-12 weeks being optimal. Remember, because of the Decanoate ester attached this is an extremely slow acting anabolic steroid; just look at the long half-life that is 15 days and you can see this fact. Due to this fact, gains will come very slow, and most will not see much due to use until 4-6 weeks have passed. At any rate, it is also recommended you end all Deca-Durabolin use at least 2 weeks before your total cycle ends. For example, if you were stacking Testosterone and Deca-Durabolin in a 12 week plan, you would end your Deca-Durabolin use at the end of week 10 and continue to supplement with Testosterone for two more weeks. If you end a cycle with Deca-Durabolin, because it is so suppressive and stays in your system for so long it will make recovery far more difficult than it needs to be.

Equipment Required to make powders  into  oils

Carrier oil (Grape seed oil)
Sterile (Syringe) Filters (0.22um Whatman filter)
Benzyl-Alcohol (BA)
Benzyl-benzoate (BB)
Sterile vials
Needles / Syringes
Glass Beaker
Organic Filtration Membrane

G1

The Way to Filter Steroid Oil

Step 1:
Attach 22 guage needle to the whatman syringe filter

Step 2:
Swab the top of the vial with alcohol wipes to sterilize it

Step 3:
Insert the 20guage syringe filtered needle into the septum of the vial (the rubber piece)

Step 4:
Insert the second needle tip into the septum to vent the pressure that will build from injecting the solution into the vial

Step 5:
Draw up the warmed solution. Having it warmed will speed up the process and make it easier to filter

Step 6:
Attach the barrel of the syringe to the whatman syringe filter. push the solution through the whatman syringe filter into the sterile vial. Use constant pressure. It will only trickle. Be sure not to apply immense pressure as that will split the syringe filter and you will have a mess everywhere

Step 7:
Detach the syringe barrel from the whatman syringe filter and draw up another 10mls of your steroid solution. Reattach to the syringe filter and filter it into the new sterile vial. .If using 10ml vials, Just repeat steps 9 thru 12 filtering 10mls of the solution in each of the vials

Final product:
Your choice as to which size vial you use. You will end up with either One 40ml vial or Two 20ml vials or Four 10mls vials at 300mg/ml

test a 80

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s